Cable tie problems come in two kinds: ties that "break" while being tightened or in service, and bundles that "come loose" over time. In both cases the cause is rarely the tie alone; more often it is a combination of size selection, fastening method, storage and the operating environment. Based on Allpum cable tie (AP series) specifications, here are the common causes for each symptom and preventive steps you can take on site.
How a cable tie works: where the stress goes
One face of the strap carries a row of fine teeth, and a pawl inside the head engages them one by one so the strap cannot slide back. When the bundle is tightened, or when weight and vibration act on it, the stress concentrates on the head, the pawl and the strap right next to the head. That is why broken ties usually fail near the head, and loose ties are often ones where the pawl never engaged the teeth properly.
Why ties break and how to prevent it
| Cause | What you see | Prevention |
|---|---|---|
| Load beyond the rating | Ties on heavy bundles or hanging items fail after a while | Move up to a wider tie; tensile strength is a limit, not a working load |
| Overtightening | Snaps near the head while tightening; cable jacket is crushed | Pull only until the bundle no longer moves |
| Nylon stiffened by cold or dry air | New ties snap in winter or in heated, dry rooms | Let ties reach room temperature first; avoid sharp bends |
| Heat beyond the operating range | Ties near heat sources discolour, deform and weaken | Consider heat-resistant APH (up to 120 °C) where 85 °C may be exceeded |
| UV exposure | Outdoor ties fade and crack on the surface | Use UV-resistant black ties in sunlight (not 100 mm) |
| Sharp edges and rubbing | The strap wears through where it touches an edge | Route away from edges and add protection |
Load: tensile strength is a limit
The tensile strength in the specification table is the limit the tie can withstand, and exceeding it may break the tie. In practice the tightening force, the bundle weight and vibration add up, so leave a margin. Allpum AP-series ties range from 80 N (AP100, 2.5 mm wide) to 715 N (AP450 / 540 / 780, 9.0 mm wide) depending on width. Rather than tightening harder, move up to a wider size. For example, AP300 is longer but, at 4.8 mm wide, has the same 220 N as AP200.
Cold and dry air: why more ties break in winter
Nylon 66 slowly absorbs and releases moisture from the air. When it dries out or gets cold it becomes harder but more vulnerable to sharp bends and impact. Ties taken straight from a sub-zero store or a winter vehicle and pulled hard tend to snap near the head, so let them reach room temperature and test one or two first. Keeping ties in their original bag until use slows changes in moisture. Our storage guide covers this in detail.

Why ties come loose and how to prevent it
- Inserted upside down If the toothed face points outward, the pawl cannot engage and the strap simply slides. Wrap with the teeth facing the bundle and feel for the click as you insert.
- Twisting after tightening Twisting a tightened tie to reposition it loads the head and strap and can damage or loosen the pawl. Position first, then tighten.
- Too loose If the bundle can move inside the tie, vibration keeps rubbing the strap and head. Tighten until the bundle does not slide when pushed by hand.
- Vibration and movement For wiring on vibrating machinery or vehicles, use more ties at closer spacing and anchor the bundle with mounts so it cannot swing.
- Releasing and reusing Standard cable ties are single-use. Forcing the pawl open to release one means you cannot rely on its grip when refastened. Use reusable cable ties where the bundle must be opened often.
A checklist before fastening
- Bundle diameter Choose a length whose max. bundle diameter comfortably exceeds the bundle (AP100 22 mm to AP780 230 mm).
- Load and vibration Choose a width (tensile strength) that suits the weight and vibration.
- Temperature and sunlight Outside -40 to 85 °C choose another material; in sunlight choose black.
- Fastening and finish Insert the right way, tighten moderately and cut the tail flush with the head.
- Inspection At routine inspections replace discoloured, cracked or loose ties with new ones.
What we check at the factory
Consistent quality in the tie itself matters as much as how it is used on site. Suryong inspects Allpum cable ties every day: an insertion check confirms the strap enters the head without being too stiff or unstable, and a fastening check confirms holding force and bundle stability. A cold-resistance test confirms the ties keep their strength and flexibility at low temperatures. Korean-made Allpum cable ties carry US UL safety certification (File E525872); Thai-made products do not carry a UL product-certification claim.







